Skip to main content

Gruebler’s Equation

Gruebler’s Equation

Degrees of freedom for planar linkages joined with common joints can be calculated through Gruebler’s equation.
Gruebler’s equation is given by the formula:
Gruebler's equation formula for calculating degrees of freedom
where,
n = total number of links in the mechanism
jp = total number of primary joints (pins or sliding joints)
jh = total number of higher-order joints (cam or gear joints)
Mechanisms and structures with varying mobility
Mechanisms and structures with varying mobility for Figure (a), (b) and (c)
Most linkages used in machines have a single degree of freedom. An example of single degree-of-freedom linkage is shown in figure (a).
Linkages with zero or negative degrees of freedom are termed locked mechanisms. Locked mechanisms are unable to move and form a structure. A truss is a structure composed of simple links and connected with pin joints and zero degrees of freedom. An example of locked mechanism is shown in figure (b).
Linkages with multiple degrees of freedom need more than one driver to precisely operate them. Generally multi-degree of freedom mechanisms are open-loop kinematic chains used for reaching and positioning, such as robotic arms and backhoes. In general, multi-degree of freedom linkages offer greater ability to precisely position a link. An example of multi-degree of freedom mechanism is shown in figure (c).

Exception to Gruebler’s Equation:

The Gruebler’s equation does not account for link geometry, in rare instances, it can lead to misleading results.
One such example is shown in the below figure (d).
Mechanism that violates the Gruebler’s equation
Figure (d): Mechanism that violates the Gruebler’s equation
Notice that above figure (d) linkage contains five links and six pin joints. Using Gruebler’s equation, this linkage has zero degrees of freedom. Of course, this suggests that the mechanism is locked. However, if all pivoted links were the same size and the distance between the joints on the frame and coupler were identical, this mechanism is capable of motion, with a single degree of freedom. The center link is redundant and because it is identical in length to the other two links attached to the frame, it does not alter the action of the linkage.
There are other examples of mechanisms that violate the Gruebler’s equation because of unique geometry. A designer must be aware that the mobility equation can, at times, lead to inconsistencies.

Comments

Post a Comment

Popular posts from this blog

Grashof’s Law

Grashof’s Law The Grashof’s law states that for a four-bar linkage system, the sum of the shortest and longest link of a planar quadrilateral linkage is less than or equal to the sum of the remaining two links, then the shortest link can rotate fully with respect to a neighboring link. Consider a four-bar-linkage. Denote the smallest link by S, the longest link by L and the & other two links by P and Q. If the Grashof’s Law condition is satisfied i.e S+L ≤ P+Q, then depending on whether shortest link ‘S’ is connected to the ground by one end, two ends, or no end there are 3 possible mechanisms. They are: Double crank mechanism Double-rocker mechanism  and Crank and Rocker Mechanism 1. Double crank mechanism In double crank mechanism, the shortest link ‘S’ is a ground link. Both input crank and output crank rotate at 360°. Grashof’s condition for double crank mechanism: s+l > p+ q Let:  ‘s’  = length of shortest link, ‘l’  = length...
3 comments
Read more

Feeler Gauge: Introduction and Types

Feeler Gauge: Introduction and Types A feeler gauge is an instrument used to measure gap widths between two flat surfaces, where it is difficult to reach. Feeler gauges are found in metrology section. Feeler gauge consist of some small lengths of steel (leaves or blades) of different thicknesses with measurements labeled on every leaf. Leaves on it are flexible enough that, even if they are all on the similar hinge, some can be stacked jointly to gauge mean values. It’s familiar to have two sets of imperial units and metric measurements though the pictured set has together size recorded on each leaf. Image source:  Wikimedia A similar tool with wires of particular diameter instead of flat leaves is used to set the gap in spark plugs to the correct size; this is done by changing the gap until the leaf of the correct thickness just fits between the flat surfaces. Image Credits:  Wonkee Donkee Tools There are many different  types of feeler gauges ....
Post a Comment
Read more