Plasma-arc Welding (PAW)

In Plasma-arc Welding (PAW) is an arc welding process, a concentrated plasma arc is produced and directed towards the weld area. The arc is stable and reaches temperatures as high as 33,000°C. A plasma is an ionized very hot gas composed of nearly same numbers of electrons and ions. The plasma starts between the tungsten electrode and the orifice by a low current pilot arc. What makes plasma-arc welding unlike other processes is that the plasma arc is concentrated because it is forced through a relatively small orifice. Operating currents usually are less than 100 A. When a filler metal is used it is fed into the arc as is done in Gas Tungsten-arc Welding. Arc and weld-zone shielding are supplied by means of an outer shielding ring and the use of inert gases like argon, helium or mixtures.

There are two methods of plasma-arc welding:

In the transferred-arc method of plasma-arc welding(in pic left side), the workpiece being welded is part of the electrical circuit. The arc transfers from the electrode to the workpiece hence the term transferred.
In the non-transferred arc method of plasma-arc welding(in pic right side), the arc occurs between the electrode and the nozzle and the heat is carried to the workpiece by the plasma gas. This thermal transfer mechanism is similar to that for an oxy-fuel flame.

Two methods of plasma-arc welding processes (a) transferred and (b) non-transferred

Compared to other arc welding processes, Plasma-arc Welding process has better arc stability, less thermal distortion, and higher energy concentration, thus permitting deeper and narrower welds. PAW has higher welding speed ranges from 120 mm/min to 1000 mm/min. A variety of metals can be welded with part thicknesses less than 6 mm.

The high heat concentration can penetrate completely through the joint with thicknesses as much as 20 mm for some titanium and aluminum alloys. In the keyhole technique, the force of the plasma arc displaces the molten metal and produces a hole at the leading edge of the weld pool. Plasma arc welding often is used rather than Gas Tungsten-arc welding for butt and lap joints because of its higher energy concentration, better arc stability and higher speed of welding. Proper training and skill are required for the operator who works on this equipment.

Comments

Grashof’s Law

Grashof’s Law The Grashof’s law states that for a four-bar linkage system, the sum of the shortest and longest link of a planar quadrilateral linkage is less than or equal to the sum of the remaining two links, then the shortest link can rotate fully with respect to a neighboring link. Consider a four-bar-linkage. Denote the smallest link by S, the longest link by L and the & other two links by P and Q. If the Grashof’s Law condition is satisfied i.e S+L ≤ P+Q, then depending on whether shortest link ‘S’ is connected to the ground by one end, two ends, or no end there are 3 possible mechanisms. They are: Double crank mechanism Double-rocker mechanism and Crank and Rocker Mechanism 1. Double crank mechanism In double crank mechanism, the shortest link ‘S’ is a ground link. Both input crank and output crank rotate at 360°. Grashof’s condition for double crank mechanism: s+l > p+ q Let: ‘s’ = length of shortest link, ‘l’ = length...

Gruebler’s Equation

Gruebler’s Equation Degrees of freedom for planar linkages joined with common joints can be calculated through Gruebler’s equation. Gruebler’s equation is given by the formula: where, n = total number of links in the mechanism j p = total number of primary joints (pins or sliding joints) j h = total number of higher-order joints (cam or gear joints) Mechanisms and structures with varying mobility for Figure (a), (b) and (c) Most linkages used in machines have a single degree of freedom. An example of single degree-of-freedom linkage is shown in figure (a). Linkages with zero or negative degrees of freedom are termed locked mechanisms. Locked mechanisms are unable to move and form a structure. A truss is a structure composed of simple links and connected with pin joints and zero degrees of freedom. An example of locked mechanism is shown in figure (b). Linkages with multiple degrees of freedom need more than one dri...

Feeler Gauge: Introduction and Types

Feeler Gauge: Introduction and Types A feeler gauge is an instrument used to measure gap widths between two flat surfaces, where it is difficult to reach. Feeler gauges are found in metrology section. Feeler gauge consist of some small lengths of steel (leaves or blades) of different thicknesses with measurements labeled on every leaf. Leaves on it are flexible enough that, even if they are all on the similar hinge, some can be stacked jointly to gauge mean values. It’s familiar to have two sets of imperial units and metric measurements though the pictured set has together size recorded on each leaf. Image source: Wikimedia A similar tool with wires of particular diameter instead of flat leaves is used to set the gap in spark plugs to the correct size; this is done by changing the gap until the leaf of the correct thickness just fits between the flat surfaces. Image Credits: Wonkee Donkee Tools There are many different types of feeler gauges ....

mechanical engineering

Search This Blog