Skip to main content

Pressure Scales

Pressure Scales

In fluid mechanics, the pressure results from a normal compressive force acting on an area. The pressure ‘P’ is defined as force (F) per unit area (A). In SI units the unit of measurement of pressure is Newtons per square meter (N/m2 ) or Pascal (Pa).
Since Pascal is a small unit of measurement of pressure, the pressure is usually referred to in kilo Pascal (kPa) or even in Mega Pascal (M Pa). The standard atmospheric pressure (Patm) at sea level is 101.3 kPa or 1.013 bar.
The gauge pressure (Pgauge) is the pressure recorded by the gauge or manometer device. In engineering calculations, absolute pressure is used and the conversion from gauge pressure to absolute pressure is carried out using the following equation.
Absolute pressure = gauge pressure + atmospheric pressure
Pabsolute = Pgauge + Patm
‘Gauge pressure‘ is the difference between ‘absolute pressure‘ and ‘atmospheric pressure‘.
Zero gauge pressure is atmospheric pressure. Also, zero absolute pressure in an ideal vacuum.
Fig. 1 gives the relation between gauge and absolute pressures.
Pressure scale
Fig 1. Gauge pressure and absolute pressure
The gauge pressure is negative whenever the absolute pressure is less than atmospheric pressure; it can be called as vacuum.
For negative pressures
Pabsolute = Patm – Pgauge

Comments

Post a Comment

Popular posts from this blog

Fundamental Concepts and Terms in Vibration

Fundamental Concepts and Terms in Vibration Vibration is a mechanical phenomenon, It is a movement first in one direction and then back again in the reverse direction. e.g: the motion of a swinging pendulum, the motion of a tuning fork. Any simple vibration is described by three factors: its amplitude; its frequency and rate of oscillation. Some of the general terms you will come across while studying on vibration topic are Oscillatory motion, Simple Harmonic Motion, Periodic Motion. now we will see the above mentioned terms in brief. Oscillatory motion is described as motion that repeats itself in a regular intervals of time. for example a sine wave or cos wave or pendulum. The time taken for an oscillation to occur is often referred to as the oscillatory period. Simple Harmonic Motion: Simple Harmonic Motion is periodic motion in which the restoring force is directly proportional to the displacement. F = -k*x A simple harmonic motion of a pendulum is an example of m...
1 comment
Read more

Grashof’s Law

Grashof’s Law The Grashof’s law states that for a four-bar linkage system, the sum of the shortest and longest link of a planar quadrilateral linkage is less than or equal to the sum of the remaining two links, then the shortest link can rotate fully with respect to a neighboring link. Consider a four-bar-linkage. Denote the smallest link by S, the longest link by L and the & other two links by P and Q. If the Grashof’s Law condition is satisfied i.e S+L ≤ P+Q, then depending on whether shortest link ‘S’ is connected to the ground by one end, two ends, or no end there are 3 possible mechanisms. They are: Double crank mechanism Double-rocker mechanism  and Crank and Rocker Mechanism 1. Double crank mechanism In double crank mechanism, the shortest link ‘S’ is a ground link. Both input crank and output crank rotate at 360°. Grashof’s condition for double crank mechanism: s+l > p+ q Let:  ‘s’  = length of shortest link, ‘l’  = length...
3 comments
Read more

Gruebler’s Equation

Gruebler’s Equation Degrees of freedom for planar linkages joined with common joints can be calculated through Gruebler’s equation. Gruebler’s equation is given by the formula: where, n = total number of links in the mechanism j p  = total number of primary joints (pins or sliding joints) j h  = total number of higher-order joints (cam or gear joints) Mechanisms and structures with varying mobility for Figure (a), (b) and (c) Most linkages used in machines have a single degree of freedom. An example of single degree-of-freedom linkage is shown in figure (a). Linkages with zero or negative degrees of freedom are termed locked mechanisms. Locked mechanisms are unable to move and form a structure. A truss is a structure composed of simple links and connected with pin joints and zero degrees of freedom. An example of locked mechanism is shown in figure (b). Linkages with multiple degrees of freedom need more than one dri...
1 comment
Read more