Skip to main content

Couple (Mechanics)

Couple (Mechanics)

The moment produced by two equal, opposite and noncollinear forces is called couple. Couples have certain unique properties and important applications in mechanics.
Considering the action of two equal and opposite forces ‘F’ and ‘-F’ a distance ‘d‘ apart, as shown in fig. 1 (a). These two forces cannot be combined into a single force because their sum in every direction is zero. Their only effect is to produce a tendency of rotation. The combined moment of two forces about an axis normal to their plane and passing through any point such as ‘O’ in their plane is the couple ‘M’. This couple has a magnitude
M = F(a + d) – Fa
or
M = F.d
Its direction is counterclockwise when viewed from above for the case illustrated. Note especially that the magnitude of the couple is independent of the distance a which locates the forces with respect to the motion center ‘O’. It follows that the moment of a couple has the same value for all the moment centers.
two equal and opposite forces makes a couple
Figure 1 (a), (b) and (c)

Vector Algebra Method:

We may also express the moment of  a couple by using vector algebra. The combined moment about points ‘O’ of the forces forming the couple of Fig. 1 (b) is
M = rA × F + rB × (-F) = (rA – rB) × F
where rA and rB are position vectors which run from point ‘O’ to arbitrary points A and B on the lines of action of ‘F’ and ‘-F’, respectively. Because rA – rB = r, we can express M as
M = r × F
Here again, the moment expression contains no reference to the moment center ‘O’ and therefore, is the same for all the moment centers. Thus, we may represent M by a free vector, as shown in Fig. 1 (c), where the direction of M is normal to the plane of the couple and the sense of M is established by the right-hand rule.
counterclockwise and clockwise couple
Figure 1 (d)
Because the couple vector ‘M’ is always perpendicular to the plane of the forces which constitute the couple, in two-dimensional analysis we can represent the sense of a couple vector as clockwise or counterclockwise by one of the conventions shown in Fig. 1 (d). Later, when we deal with couple vectors in three-dimensional problems, we will make full use of vector notation to represent them and the mathematics will automatically account for their sense.

Equivalent Couples:

Changing the values of ‘F’ and ‘d‘ does not change a given couple as long as the product ‘F.d’ remains the same. Likewise, a couple is not affected if the forces act in a direction but parallel plane. Fig. 2, shows four different configurations of the same couple M. In each of the four cases, the couples are equivalent and are described by the same free vector which represents the identical tendencies to rotate the body.
four different configurations of same couple
Figure 2

Force-Coupled Systems:

The effect of force acting on a body is the tendency to push or pull the body in the direction of the force and to rotate the body about any fixed axis which doesn’t intersect the line of force. We can represent this dual effect more easily by replacing the given force by an equal parallel force and a couple to compensate for the change in the moment of the force.
The replacement of a force by a force and a couple is illustrated in Fig. 3, where the given force F acting at a point ‘A’ is replaced by an equal force ‘F’ at some point ‘B’ and counter clockwise couple M = F.d. The transfer is seen in the middle figure, where the equal and opposite forces ‘F’ and ‘-F’ are added at point ‘B’ without introducing any net external effects on the body. We now see that the original force at point ‘A’ and the equal and opposite force one at point ‘B’ constitute the couple M = F.d, which is counter clockwise for the sample chosen, as shown in the right-hand part of the figure 3. Thus, we have replaced the original force at A by the same force acting at a different point B and a couple, without altering the external effects of the original force on the body. The combination of the force and couple in the right-hand part of Fig. 3 is referred to as a force-couple system.
By reversing this process, we can combine a given couple and a force which lies in the plane of the couple (normal to the couple vector) to produce a single, equivalent force. Replacement of  a force by an equivalent force-couple system and the reverse procedure, have many applications in mechanics and should be mastered.
combination of force and couple
Figure 3

Comments

Post a Comment

Popular posts from this blog

Grashof’s Law

Grashof’s Law The Grashof’s law states that for a four-bar linkage system, the sum of the shortest and longest link of a planar quadrilateral linkage is less than or equal to the sum of the remaining two links, then the shortest link can rotate fully with respect to a neighboring link. Consider a four-bar-linkage. Denote the smallest link by S, the longest link by L and the & other two links by P and Q. If the Grashof’s Law condition is satisfied i.e S+L ≤ P+Q, then depending on whether shortest link ‘S’ is connected to the ground by one end, two ends, or no end there are 3 possible mechanisms. They are: Double crank mechanism Double-rocker mechanism  and Crank and Rocker Mechanism 1. Double crank mechanism In double crank mechanism, the shortest link ‘S’ is a ground link. Both input crank and output crank rotate at 360°. Grashof’s condition for double crank mechanism: s+l > p+ q Let:  ‘s’  = length of shortest link, ‘l’  = length...
3 comments
Read more

Gruebler’s Equation

Gruebler’s Equation Degrees of freedom for planar linkages joined with common joints can be calculated through Gruebler’s equation. Gruebler’s equation is given by the formula: where, n = total number of links in the mechanism j p  = total number of primary joints (pins or sliding joints) j h  = total number of higher-order joints (cam or gear joints) Mechanisms and structures with varying mobility for Figure (a), (b) and (c) Most linkages used in machines have a single degree of freedom. An example of single degree-of-freedom linkage is shown in figure (a). Linkages with zero or negative degrees of freedom are termed locked mechanisms. Locked mechanisms are unable to move and form a structure. A truss is a structure composed of simple links and connected with pin joints and zero degrees of freedom. An example of locked mechanism is shown in figure (b). Linkages with multiple degrees of freedom need more than one dri...
1 comment
Read more

Fundamental Concepts and Terms in Vibration

Fundamental Concepts and Terms in Vibration Vibration is a mechanical phenomenon, It is a movement first in one direction and then back again in the reverse direction. e.g: the motion of a swinging pendulum, the motion of a tuning fork. Any simple vibration is described by three factors: its amplitude; its frequency and rate of oscillation. Some of the general terms you will come across while studying on vibration topic are Oscillatory motion, Simple Harmonic Motion, Periodic Motion. now we will see the above mentioned terms in brief. Oscillatory motion is described as motion that repeats itself in a regular intervals of time. for example a sine wave or cos wave or pendulum. The time taken for an oscillation to occur is often referred to as the oscillatory period. Simple Harmonic Motion: Simple Harmonic Motion is periodic motion in which the restoring force is directly proportional to the displacement. F = -k*x A simple harmonic motion of a pendulum is an example of m...
1 comment
Read more