Skip to main content

How to Choose the Ideal Heat-transfer Fluid for Solar Water Heating System ?

How to Choose the Ideal Heat-transfer Fluid for Solar Water Heating System ?

When deciding on which heat-transfer fluid best suits your needs, there are some crucial factors to take into account. In solar water heating systems, these fluids are responsible for transporting heat through heat exchangers and solar collectors to the heat storage tanks. Needless to say, the decision on which fluid to use is a crucial one.
For starters, you should consider:
  • Thermal capacity: The ability to store heat.
  • Boiling point and freezing point: The temperature at which it boils or at which liquid transforms into a solid, respectively.
  • Flash point: The minimum temperature at which the vapor above a liquid is able to be ignited in air.
  • Viscosity: The liquid’s resistance to sheer forces.
  • Coefficient of expansion: A material’s small changes in length or volume due to minimal temperature changes.

Different Heat-transfer Fluids

Air does not freeze, boil, or corrode. The drawback is that it has an extremely low heat capacity and is prone to leaking out of collectors, ducts, and other areas of the unit.
Water doesn’t cost much, is nontoxic, and, due to a high specific heat and extremely low viscosity, it’s also easy to pump. The problem with water is that it has a high freezing point, low boiling point, and can be corrosive if neutral pH levels are not maintained. If you elect to use water, use soft water, as hard water tends to cause the formation of mineral deposits in your system.
Glycol/water mixtures typically have around a 50/50 glycol-to-water ratio. Ethylene and propylene glycol are considered antifreezes, and will provide protection against freezing if the proper concentration is maintained. These fluids degrade over time and should be replaced every 3 years or so.
Hydrocarbon oils have a lower specific heat and higher viscosity than water, meaning they require more energy to pump. Advantages of these oils are that they are relatively inexpensive and feature a low freezing point, making them ideal for cold temperatures.
Refrigerants and phase change fluids are often used in refrigerators, air conditioners, heat pumps, and other similarly common appliances. These fluids have a high heat capacity and low boiling point, which allows a small amount of the refrigerant to transfer a relatively large amount of heat efficiently. They also respond to solar heat rapidly, making them less dependent on sunlight than other sources of solar power.
Silicones have an incredibly high boiling point and low freezing point. Similar to hydrocarbon oils, these fluids have low heat capacities and a high viscosity and, thus, require more energy to pump. Unfortunately, silicones leak easily through even the smallest of holes.

What to Choose

There are many factors to consider when choosing a heat-transfer fluid. When making your decision, think about the temperatures the fluid will be exposed to. Naturally, fluids that will be exposed to high temperatures should have a high boiling point, while those that will face more frigid temperatures should have a lower freezing point. The good news is that, with so many to choose, you can easily find one that fits your purposes.

Comments

Post a Comment

Popular posts from this blog

Fundamental Concepts and Terms in Vibration

Fundamental Concepts and Terms in Vibration Vibration is a mechanical phenomenon, It is a movement first in one direction and then back again in the reverse direction. e.g: the motion of a swinging pendulum, the motion of a tuning fork. Any simple vibration is described by three factors: its amplitude; its frequency and rate of oscillation. Some of the general terms you will come across while studying on vibration topic are Oscillatory motion, Simple Harmonic Motion, Periodic Motion. now we will see the above mentioned terms in brief. Oscillatory motion is described as motion that repeats itself in a regular intervals of time. for example a sine wave or cos wave or pendulum. The time taken for an oscillation to occur is often referred to as the oscillatory period. Simple Harmonic Motion: Simple Harmonic Motion is periodic motion in which the restoring force is directly proportional to the displacement. F = -k*x A simple harmonic motion of a pendulum is an example of m...
1 comment
Read more

Grashof’s Law

Grashof’s Law The Grashof’s law states that for a four-bar linkage system, the sum of the shortest and longest link of a planar quadrilateral linkage is less than or equal to the sum of the remaining two links, then the shortest link can rotate fully with respect to a neighboring link. Consider a four-bar-linkage. Denote the smallest link by S, the longest link by L and the & other two links by P and Q. If the Grashof’s Law condition is satisfied i.e S+L ≤ P+Q, then depending on whether shortest link ‘S’ is connected to the ground by one end, two ends, or no end there are 3 possible mechanisms. They are: Double crank mechanism Double-rocker mechanism  and Crank and Rocker Mechanism 1. Double crank mechanism In double crank mechanism, the shortest link ‘S’ is a ground link. Both input crank and output crank rotate at 360°. Grashof’s condition for double crank mechanism: s+l > p+ q Let:  ‘s’  = length of shortest link, ‘l’  = length...
3 comments
Read more

Gruebler’s Equation

Gruebler’s Equation Degrees of freedom for planar linkages joined with common joints can be calculated through Gruebler’s equation. Gruebler’s equation is given by the formula: where, n = total number of links in the mechanism j p  = total number of primary joints (pins or sliding joints) j h  = total number of higher-order joints (cam or gear joints) Mechanisms and structures with varying mobility for Figure (a), (b) and (c) Most linkages used in machines have a single degree of freedom. An example of single degree-of-freedom linkage is shown in figure (a). Linkages with zero or negative degrees of freedom are termed locked mechanisms. Locked mechanisms are unable to move and form a structure. A truss is a structure composed of simple links and connected with pin joints and zero degrees of freedom. An example of locked mechanism is shown in figure (b). Linkages with multiple degrees of freedom need more than one dri...
1 comment
Read more