Skip to main content

Types of Mechanical Forces

Types of Mechanical Forces

A force exerted on a body can cause a change in either the shape or the motion of the body. The unit of force in SI system is the newton (N) and CGS system is dyne. No solid body is perfectly rigid and when forces are applied to it, changes in dimensions occur. Such changes are not always perceptible to the human eye since they are negligible. For example, the span of a bridge will sag under the weight of a vehicle and a spanner will bend slightly when tightening a nut. It is important for civil engineers and designers to appreciate the effects of forces on materials, together with their mechanical properties of materials.
There are three main types of mechanical forces that can act on a body. They are:
  1. Tensile force
  2. Compressive force and
  3. Shear force

1. Tensile force

Tensile force that tends to stretch a material, as shown in the figure 1 below.
Tensile force
Figure 1: Tensile force
For example,
  1. Rubber bands, when stretched, are in tension.
  2. The rope or cable of a crane carrying a load is in tension.
  3. When a nut is tightened, a bolt is under tension.
A tensile force will increases the length of the material on which it acts.
Also read: Types of Loads

2. Compressive force

Compressive force that tends to squeeze or crush a material, as shown in the figure 2 below.
Compressive force
Figure 2: Compressive force
For example,
  1. A pillar supporting a bridge is in compression.
  2. The sole of a shoe is in compression.
  3. The jib of a crane is in compression.
A compressive force will decrease the length of the material on which it acts.

3. Shear force

Shear force that tends to slide one face of the material over an adjacent face.
Shear force
Figure 3: Shear force
For example,
  1. A rivet holding two plates together is in shear if a tensile force is applied between the plates as shown in Figure 3.
  2. A guillotine cutting sheet metal, or garden shears, each provide a shear force.
  3. A horizontal beam is subject to shear force.
  4. Transmission joints on cars are subject to shear forces.
A shear force can cause a material to bend, slide or twist.

Comments

Post a Comment

Popular posts from this blog

Fundamental Concepts and Terms in Vibration

Fundamental Concepts and Terms in Vibration Vibration is a mechanical phenomenon, It is a movement first in one direction and then back again in the reverse direction. e.g: the motion of a swinging pendulum, the motion of a tuning fork. Any simple vibration is described by three factors: its amplitude; its frequency and rate of oscillation. Some of the general terms you will come across while studying on vibration topic are Oscillatory motion, Simple Harmonic Motion, Periodic Motion. now we will see the above mentioned terms in brief. Oscillatory motion is described as motion that repeats itself in a regular intervals of time. for example a sine wave or cos wave or pendulum. The time taken for an oscillation to occur is often referred to as the oscillatory period. Simple Harmonic Motion: Simple Harmonic Motion is periodic motion in which the restoring force is directly proportional to the displacement. F = -k*x A simple harmonic motion of a pendulum is an example of m...
1 comment
Read more

Grashof’s Law

Grashof’s Law The Grashof’s law states that for a four-bar linkage system, the sum of the shortest and longest link of a planar quadrilateral linkage is less than or equal to the sum of the remaining two links, then the shortest link can rotate fully with respect to a neighboring link. Consider a four-bar-linkage. Denote the smallest link by S, the longest link by L and the & other two links by P and Q. If the Grashof’s Law condition is satisfied i.e S+L ≤ P+Q, then depending on whether shortest link ‘S’ is connected to the ground by one end, two ends, or no end there are 3 possible mechanisms. They are: Double crank mechanism Double-rocker mechanism  and Crank and Rocker Mechanism 1. Double crank mechanism In double crank mechanism, the shortest link ‘S’ is a ground link. Both input crank and output crank rotate at 360°. Grashof’s condition for double crank mechanism: s+l > p+ q Let:  ‘s’  = length of shortest link, ‘l’  = length...
3 comments
Read more

Gruebler’s Equation

Gruebler’s Equation Degrees of freedom for planar linkages joined with common joints can be calculated through Gruebler’s equation. Gruebler’s equation is given by the formula: where, n = total number of links in the mechanism j p  = total number of primary joints (pins or sliding joints) j h  = total number of higher-order joints (cam or gear joints) Mechanisms and structures with varying mobility for Figure (a), (b) and (c) Most linkages used in machines have a single degree of freedom. An example of single degree-of-freedom linkage is shown in figure (a). Linkages with zero or negative degrees of freedom are termed locked mechanisms. Locked mechanisms are unable to move and form a structure. A truss is a structure composed of simple links and connected with pin joints and zero degrees of freedom. An example of locked mechanism is shown in figure (b). Linkages with multiple degrees of freedom need more than one dri...
1 comment
Read more