Skip to main content

Boilers: Introduction and Classification

Boilers: Introduction and Classification

  • The boiler system comprises a feed-water system, steam system, and fuel system. The feed-water system supplies treated water to the boiler and regulate it automatically to meet the steam demand. Various valves and controls are provided to access for maintenance and monitoring.
  • The steam system heats and vaporizes the feed water and controls steam produced in the boiler. Steam is directed through a piping system to the application. Throughout the system, steam pressure is regulated using valves and monitored with steam pressure gauges.
  • The fuel system consists of all equipment used to supply of fuel to generate the necessary heat. The equipment required in the fuel system depends on the type of fuel used in the system.

Boilers Classification:

There are a large number of boiler designs, but boilers can be classified according to the following criteria:
1. According to Relative Passage of water and hot gases:
  1. Water Tube Boiler: A boiler in which the water flows through some small tubes which are surrounded by hot combustion gases, e.g., Babcock and Wilcox, Stirling, Benson boilers, etc.
  2. Fire-tube Boiler: The hot combustion gases pass through the boiler tubes, which are surrounded by water, e.g., Lancashire, Cochran, locomotive boilers, etc.
2. According to Water Circulation Arrangement:
  1. Natural Circulation: Water circulates in the boiler due to density difference of hot and water, e.g.,Babcock and Wilcox boilers, Lancashire boilers, Cochran, locomotive boilers, etc.
  2. Forced Circulation: A water pump forces the water along its path, therefore, the steam generation rate increases, Eg: Benson, La Mont, Velox boilers, etc.
3. According to the Use:
  1. Stationary Boiler: These boilers are used for power plants or processes steam in plants.
  2. Portable Boiler: These are small units of mobile and are used for temporary uses at the sites.
  3. Locomotive: These are specially designed boilers. They produce steam to drive railway engines.
  4. Marine Boiler: These are used on ships.
4. According to Position of the Boilers:
  • Horizontal, inclined or vertical boilers
5. According to the Position of Furnace
  1. Internally fired: The furnace is located inside the shell, e.g., Cochran, Lancashire boilers, etc.
  2. Externally fired: The furnace is located outside the boiler shell, e.g., Babcock and Wilcox, Stirling boilers, etc.
6. According to Pressure of steam generated
  • Low-pressure boiler: a boiler which produces steam at a pressure of 15-20 bar is called a low-pressure boiler. This steam is used for process heating.
  • Medium-pressure boiler: It has a working pressure of steam from 20 bars to 80 bars and is used for power generation or combined use of power generation and process heating.
  • High-pressure boiler: It produces steam at a pressure of more than 80 bars.
  • Sub-critical boiler: If a boiler produces steam at a pressure which is less than the critical pressure, it is called as a subcritical boiler.
  • Supercritical boiler: These boilers provide steam at a pressure greater than the critical pressure. These boilers do not have an evaporator and the water directly flashes into steam, and thus they are called once through boilers.
7. According to charge in the furnace.
  • Pulverized fuel,
  • Supercharged fuel and
  • Fluidized bed combustion boilers.

Comments

Post a Comment

Popular posts from this blog

Fundamental Concepts and Terms in Vibration

Fundamental Concepts and Terms in Vibration Vibration is a mechanical phenomenon, It is a movement first in one direction and then back again in the reverse direction. e.g: the motion of a swinging pendulum, the motion of a tuning fork. Any simple vibration is described by three factors: its amplitude; its frequency and rate of oscillation. Some of the general terms you will come across while studying on vibration topic are Oscillatory motion, Simple Harmonic Motion, Periodic Motion. now we will see the above mentioned terms in brief. Oscillatory motion is described as motion that repeats itself in a regular intervals of time. for example a sine wave or cos wave or pendulum. The time taken for an oscillation to occur is often referred to as the oscillatory period. Simple Harmonic Motion: Simple Harmonic Motion is periodic motion in which the restoring force is directly proportional to the displacement. F = -k*x A simple harmonic motion of a pendulum is an example of m...
1 comment
Read more

Grashof’s Law

Grashof’s Law The Grashof’s law states that for a four-bar linkage system, the sum of the shortest and longest link of a planar quadrilateral linkage is less than or equal to the sum of the remaining two links, then the shortest link can rotate fully with respect to a neighboring link. Consider a four-bar-linkage. Denote the smallest link by S, the longest link by L and the & other two links by P and Q. If the Grashof’s Law condition is satisfied i.e S+L ≤ P+Q, then depending on whether shortest link ‘S’ is connected to the ground by one end, two ends, or no end there are 3 possible mechanisms. They are: Double crank mechanism Double-rocker mechanism  and Crank and Rocker Mechanism 1. Double crank mechanism In double crank mechanism, the shortest link ‘S’ is a ground link. Both input crank and output crank rotate at 360°. Grashof’s condition for double crank mechanism: s+l > p+ q Let:  ‘s’  = length of shortest link, ‘l’  = length...
3 comments
Read more

Gruebler’s Equation

Gruebler’s Equation Degrees of freedom for planar linkages joined with common joints can be calculated through Gruebler’s equation. Gruebler’s equation is given by the formula: where, n = total number of links in the mechanism j p  = total number of primary joints (pins or sliding joints) j h  = total number of higher-order joints (cam or gear joints) Mechanisms and structures with varying mobility for Figure (a), (b) and (c) Most linkages used in machines have a single degree of freedom. An example of single degree-of-freedom linkage is shown in figure (a). Linkages with zero or negative degrees of freedom are termed locked mechanisms. Locked mechanisms are unable to move and form a structure. A truss is a structure composed of simple links and connected with pin joints and zero degrees of freedom. An example of locked mechanism is shown in figure (b). Linkages with multiple degrees of freedom need more than one dri...
1 comment
Read more